-40%
Dental Wireless LED Lamp Curing Light Broad Band Cure GOUS
$ 21.06
- Description
- Size Guide
Description
Description1S Curing:
Technical Parameters:
Light Source:
Broad Band LED;
Wavelength Range:
385 - 515 nm;
Light Intensity:
> 2300mW / cm²;
Battery:
Lithium-ion battery (total running time when the battery is fully charged: at least 80 minutes);
Power Adapter Input Power:
AC 100-240V 50 / 60Hz;
Charging time: about 45 minutes;
Size:Handle:
Φ20 mm × 240 mm; Charging stand: Φ63 mm × 30 mm (all of the above are the largest size)
Weight: Handle: 96 grams; Charging seat: 99 grams;
Operating ambient temperature: + 10℃ - + 40℃(+ 50 °F - + 70°F);
Operating relative humidity: 30% - 75%;
Operating environment pressure:
700hPa - 1060hPa;
Package Contents:
1 × host handle;
1 × charging base;
1 × power adapter;
1 × user manual.
Operation and function description:
The entire handle is only one button, light built-in button.
1. For the first time, charge the light curing handle first. Plug the USB cable of the charger into the USB port of the power adapter, plug the power adapter into the power socket, and finally
Put the handle on the charging stand; or, insert the USB cable plug of the charging stand into the USB port of the computer, and then put the handle on the charging stand. Charging instructions are as follows:
| Emerald Flashing | Battery charging;
| Emerald green light | battery fully charged; handle removed the charging seat, the restoration of the previous working mode.
2. Working mode selection, by pressing the button for 2 seconds to release to switch the working mode.
| Blinking Blue | Progressive mode, working time 10 seconds, light intensity 0-5 seconds from 0-1200mW / cm², 5-10 seconds 1200mW / cm².
| Solid blue | Fast mode, working time 3 seconds, light intensity 2300mW / cm ²
3. Turn the light curing lamp on and off, press the button briefly.
4. Switch machine, in standby mode, press the button a short time to open the instrument; stop any operation for 60 seconds, into the ultra-low power standby.
T4 curing light
adopts the principle of ray radiation to solidify the light-sensitive resin by shooting at it in a short time.
This curing light with adjustable working time, working time visual, curing efficiency higher and
intelligent ze
d charging stand.
Feature:
Four modes of working time: 10,20,30,40 seconds
Working modes: Full power
The battery can be replaced
The optical fiber can be autoclaved to the high temperature and pressure.
Automatic shut down function(120s no any operation)
Technical Specifications:
Power supply: Rechargeable Lithium battery
Battery voltage and capacity: 4.2V/2000mAh
Input of adapter: 100V to 240V~50Hz/60Hz
Light intensity: 1400MW/CM
2
Light source: A. Blue ray
B. Wave length:420nm-480nm
Packing list:
Main unit
Optical fiber
Light hood
Adaptor
Working condition:
A.environment temperature: 5℃ to 40℃
B.relative humidity: ≤80%
Consumption power: ≤8W
protection type against electrical shock: Class Ⅱ
Protection against electrical shock: Type B
Introduction:
Thank you for choosing D2 curing light unit.This unit is a kind of new type curing device which using the high-power, high—brilliance, pure blue light LED as light source,with the advance light guide rod.
1.The unit is using the LED which has 430—485nm wavelength in the dental operation.
2. LED Screen, easy to check.
3. When works it generates little heat and does not need
a fans to cool the unit ,noiseless and without vibration,
4. This unit has a Li large capacity battery,it can be used for a long one with full charging.
5.Because there are no cables connect to the handpiece,it could be used very conveniently.
6. Three Mode:
“01”Mode:Gradually mode
“02”Mode:Flashing mode.
“03”Mode:All light mode.
7. Automatically power down:when the unit is standby and
without pressing button for 8 minutes,this unit will be turned
off automatically.
8. low battery alert:Every time open the unit power if the voltage of the battery is lower than the set point, this unit will be alarm.
Specification:
Size………………….dia 22*175mm(unit)
Safety kind……………Ordinary type B.non—continuous service Ip40.Class 2.
Input voltage……………100—240V,50-60HZ(we will send the correct plug according to buyer’s location)
Battery capacity………………·2000Mah
Wavelength………430-485nm
Intensity-………
5W≥1800mw/cm2
Solidification effect……20s,>3mm (3W) ,6s,3mm (10W)
Packing List:
1Main unit…………………l set
2Light guide rod…………1 pc
3 Battery………………………1 Pc
4 Charger……………………1 set
5 Adaptor…………………… 1 pc
6 Light cover plate……… 1 pc
7 User manual (English)…………………1 pc
D5 /D6 curing light:
Features
:
1
.
Light intensity: 1100-1600mW/cm2(tested by different brand meters), 5 watt LED
2
.
BEEP at each 5-seconds to indicate remaining curing time
3
.
Various Curing Time: seven preset curing time 5/10/15/20/25/30/40 seconds.
4
.
Three Preset Programs
a. Fast mode: Full power all the time
b. Soft 1 mode: Generally increasing power in first 5 seconds, then full power till the end.
c. Soft 2 mode: Generally increasing power in first 5 seconds, then half power till the end.
5.
Inner Build-in light meter within the base
6
.
Cord/cordless inchargeable
When ruuning out of the battery, the unit can be operated directly with the switching power adapter.
7.
High Output:
Full supply of power can satisfy 10-second curing time for 200 times.
8.
Fully guaranteed for one year
Standard accessory:
1.handpiece 1pc
2.charging base 1pc
3.charger 1pc
4.eye-protecting cover 3 pcs
5.optic light guide 1pc
6.user manual 1pc
510(K) Number: K192233
Regulation Number: 21 CFR 872.6070
Product Code: EBZ
FDA Statement
The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies.
If so, you can bid on this item only if you are an authorized purchaser.
If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item.